Surface Cleaning & Preparation is the key to any successful coating system. Therefore, using specialist products can significantly reduce the time spent in preparation and application.
The products below are designed for areas such as:
- Cleaning & Degreasing
- Green Growth Removal
- Facade Cleaning
- Pre-Paint Cleaning
- Surface Etch
- Fungal Growth, Algae and Dirt Removal
- Floor Cleaner
Cleaning & Degreasing
Rust-Oleum Cleaner/Degreaser for floors is a concentrated, alkaline, non-flammable, virtually odour-free cleaning/degreasing solution.
- Removes grease, oil and other contaminations
- Virtually odour free
- Non-flammable
- 6-8 m²/l coverage
Should be used to remove grease, oil, proteins dirt and many other surface contaminants from coated, mineral and steel substrates. Should be applied with an artificial sponge, cloth or stiff nylon brush or broom. Can also be used as an additive for high-pressure (steam) cleaning.
Epoxyshield Cleaner Degreaser (TDS)
ND14 Cleaner Degreaser
Concentrated, alkaline, non-flammable, virtually odour free cleaning and degreasing solution. Removes grease, oil, proteins , dirt and many other contaminants from coated, mineral and metal substrates
- Use as additive for high pressure cleaning
- Low concentration is sufficient (3-5%)
- Non-flammable, virtually odour-free
- Can also be applied by brush, mop or broom
After cleaning, remove any remaining water and allow the surface to dry, as moisture left on the surface or entrapped into pores may cause premature failure of the coating system.
Colour: transparent.
Remmers Green Growth Remover
Special detergent for removing green growth on terraces, stone floor and walls.
- Self-actively removes organic soiling with a deep cleaning effect
- No further washing of the surface needed
- 24 hours of reaction time
- Can be used pure or diluted with water
- Long-term effect if applied undiluted
- Does not contain active chlorine
- Delicate on the substrate
Removes ugly green growth on concrete, clinker, natural stone, renders and painted surfaces, indoors and outdoors. Just spray on!
Arte Mundit – Facade Cleaner
Arte Mundit is a self-vulcanising cleaning paste for thorough, water-free removal of dust, soot, nicotine residue and other soiling on inte-rior walls, ceilings, floors, stucco, natural stone, marble, concrete, brick, render, gypsum sculptures, polished wood, synthetic materials, etc. Arte Mundit is an environmentally correct cleaning paste on a natural raw material base. The fresh product vulcanises by drying into an elastic rubber with good soil binding capacity. Arte Mundit does not contain any organic solvents, surface active agents or inorganic salts.
Facade Cleaning Paste
Remmers Facade Cleaner Paste is suitable for all facade surfaces made of clinker, brick and natural stone as well as for sculptures. It is not suitable for fair-faced masonry work made of sand-lime brick. It does not dissolve the remains of mortar. Facade Cleaner Paste is a ready to use, slightly acidic, thixotropic facade cleaner paste for clinker, brick and natural stone surfaces. Since the paste is not highly acidic, there is very little loss of substance. Dark types of stone may become lighter in colour if the paste is left on the stone for a long time. Because of its thixotropic formulation, it can be applied cleanly and efficiently and the material does not run.
Pre Paint Cleaner
Effective, concentrated biodegradable cleaner to clean all types of surfaces prior to painting. No additional washing with water is required – saves time and money!
- Effortlessly removes all organic and anorganic pollution
- Biodegradable formulation
- No further cleaning with water is needed after wiping the surface
- Makes the surface anti-static to prevent adhesion of dust prior to painting
- Does not foam
- Non-flammable, virtually odour-free
- Very easy to apply by cloth
Pre-paint Cleaner cleans and degrease surfaces before painting. Suitable for all types of surfaces. Not flammable, not corrosive and nearly odourless.
Surfa-Etch
Etching Solution for etching smooth concrete surfaces, masonry, galvanized steel and aluminum before applying a coating system
- Improves the adhesion of coating systems
- Neutralizes alkaline salts
- Also ideal to remove ´white rust´ from metal
- Easy to use
- No objectionable odour or fumes
- Non-flammable
Apply Surfa-Etch® 108 Etching Solution liberally and scrub it into the surface. Allow to stand for 10-15 minutes, depending on temperature, and clean thoroughly by flushing with plenty of fresh water. After cleaning, remove any remaining water and allow the surface to dry, as moisture left on the surface or entrapped into pores may cause premature failure of the coating system.
AMW Fungicidal Wash
Ready-mix moss and algae remover for walls and roofs.
- Effectively removes algae, moss, fungi and dirt
- Officially HSE-approved biocide, HSE approval no. 9225
- Does not smell & non-hazardous to work with
- Does not attack glass or PVC
- Use on bituminous substrates, concrete, masonry, plaster and woodwork
Apply AMW abundantly, preferably by brush, and wait 12 hours. Dry-brush and remove dust prior to painting, or clean with high-pressure water and let the surface dry. Affected by heavy rainfall for at least 4 hours after application. If doubtful re-apply. Ensure residues are substantially diluted with water before entering drains etc.
Floor Cleaner
Lightly foaming alkaline degreaser based on surface-active substances, cleaning enhancers and lye.
- Very suitable for the removal of grease, dirt, soot and fire damage
- Can be used for daily maintenance or periodic cleaning
- For cleaning concrete or coated floors
- Non-flammable, virtually odour-free
- Can also be applied by brush, mop, broom or scrubbing machine
Dilute 1:8 with water for daily cleaning, for periodic cleaning or stubborn soiling use 1: 2 dilution.
Leave a Reply
Your email is safe with us.